Industry News-SINO Technology Co., Ltd.

No data

What are the installation steps for a smart health-care bed?

What are the installation steps for a smart health-care bed? The installation procedure is as follows: 1. Two brake locks are installed on the casters of the smart health-care bed; these two braked casters are mounted diagonally in the screw holes on the bed frame legs. The remaining two casters are then installed in the screw holes on the other two base legs. 2. Installation of the rear bed panel: Connect the rear bed panel to the bed frame using the rear frame pivot pin, and then secure the pin with split pins. 3. Installation of the smart bed headboard: Align the holes on both sides of the headboard with the corresponding holes on the back bed panel, insert the components, and tighten the fastening screws on both sides. 4. Installation of the rear air springs: Lift the rear bed section to a 90-degree upright position, screw one end of the rear air spring into the air-spring support bracket at the bottom of the rear bed, connect the lower air-spring support bracket to the U-shaped bed frame using a pivot pin, and then secure the pin with split pins. 5. Installation of the side air springs on the smart health-care bed; then press the side-control button to set the side bed section to a horizontal position. 6. Installation of the foot-end bed panel: First flip the foot-end bed panel over, connect the tube-shaped support brackets on the panel to the corresponding brackets on the bed frame using pivot pins, and secure the connections with split pins. Next, re-tighten the screws on both sides of the tube-slide bracket, align the holes on the tube-slide brackets with the screws on the bracket, and finally tighten the screws with a wrench. Finally, align the connecting holes between the foot-end bed panel and the thigh-end bed panel, pass the triangular bracket pivot pin through these holes, and then…

2022

What are the features of a smart health-care bed?

As China’s population ages at an accelerating pace, the proportion of older adults is steadily increasing, driving growing demand for nursing beds in the domestic elderly-care market. Once confined to medical institutions, multifunctional smart rehabilitation beds are now gradually making their way into nursing homes, home-based elderly-care service centers, and private households. These smart beds are categorized into electric smart rehabilitation beds, manual smart rehabilitation beds, and standard smart rehabilitation beds, designed for use during hospital stays or at-home care for seniors and patients with limited mobility. Their primary purpose is to facilitate caregiving and promote the recovery of elderly individuals and patients. Based on the number of imported motors, they are distinguished by motor quality, sophisticated engineering design, and high-end features. Initially, such beds were mainly used as monitoring equipment in intensive-care units for critically ill patients; however, with advances in technology, electric smart rehabilitation beds featuring home-friendly designs have emerged and are increasingly being adopted for home-based care. Multifunctional manual smart rehabilitation beds are generally classified according to the number of control levers: three-lever multifunctional beds, two-lever three-fold beds, and single-lever rocking beds. Their key characteristics include lever mechanisms and a variety of accessories—such as bedside commodes—as well as thoughtful engineering design and the selection of diverse materials, making them suitable for all departments in hospital inpatient wards. Standard nursing beds are available in straight-frame and flat-bed configurations, and may also include simple manually operated beds, which are widely used in hospitals, nursing homes, senior-service centers, clinics, and other settings. Multi-function

2022

Next, let’s discuss how to use the smart health-care bed.

Next, let’s discuss how to use the smart health-care bed. The operating procedures are as follows: 1. Adjusting the bed’s body position: Grasp the head-position control handle, release the self-locking mechanism of the air spring, and extend the piston rod to slowly raise the head-end section of the bed surface. When the desired angle is reached, release the handle, and the bed surface will lock in that position. Conversely, press down on the handle to lower the head end. In addition, if a patient lying supine on the smart health-care bed wishes to turn onto their side, first pull out the small side headboard on one side, lower the corresponding side guardrail, and then, with one hand, press the control button on the outer side of the bed surface to release the self-locking mechanism of the side air spring. This will extend the piston rod, causing the side bed surface to rise slowly; when the desired angle is achieved, release the control button to lock the bed surface in that position, thereby completing the lateral decubitus position starting from the face. Note: The reverse procedure can be performed in the same way. 2. Using the bed’s commode: Turn the commode handle clockwise, and the commode lid will automatically open; the commode will then slide horizontally toward the patient’s buttocks, facilitating defecation or cleansing of the perineal area. Turning the commode handle counterclockwise will close the defecation lid, bringing it flush with the bed surface, and the commode bowl will automatically move to the operator’s side for collection and cleaning by the nurse. After cleaning, the commode bowl will be returned to the commode rack for reuse. 3. Smart

2022

An Interpretation of the Five-Year Action Plan for Improving and Upgrading the Rural Living Environment (2021–2025)

Recently, the General Office of the CPC Central Committee and the General Office of the State Council issued the Five-Year Action Plan for Improving and Upgrading the Rural Living Environment (2021–2025) and circulated a notice requiring all regions and departments to implement it conscientiously in light of their specific circumstances. The plan explicitly calls for solid progress in the rural toilet renovation campaign and vigorous efforts to build ecologically sound, livable, and beautiful villages across the board.

2021

Interpretation of Issue 17 of “Improving the Rural Living Environment”

On November 19, 2021, the Office for Promoting Rural Living Environment Improvement under the Ministry of Agriculture and Rural Affairs released the 17th issue of its briefing, titled “Rural Living Environment Improvement,” which primarily focuses on typical technical models for rural toilet renovation in arid and cold regions.

2022

Suggestions on “Ecological Revitalization of Rural Areas” in the Context of Rural Revitalization

“Prosperous industries, a livable ecological environment, refined rural customs, effective governance, and affluent livelihoods” constitute the overarching requirements for implementing the Rural Revitalization Strategy as set forth in the report to the 19th National Congress of the Communist Party of China. To ensure coordinated planning and scientific advancement of this strategy, General Secretary Xi Jinping put forward the “Five Revitalizations” thesis: “revitalization of rural industries, revitalization of rural talent, revitalization of rural culture, revitalization of the rural ecology, and revitalization of rural organizations.” With regard to promoting “rural ecological revitalization,” it is essential to strengthen resource protection and efficient resource utilization, focus on addressing prominent environmental problems in rural areas, advance the development of beautiful and livable villages, and continuously improve the rural living environment.

2022

< 1 2 3 4 >

Crude Oil Dehydration & Desalting Skids Manufacturer | Sino Technology (STC)

Phone: +86 546 877 1068
Email: sino-tech@slofzx.com
Address: Building 45, No. 396 Emeishan Road, Huangdao District, Qingdao

Official Account QR Code